Disc Makers 1 Betriebsanweisung Seite 1

User Guide v.1.0 www.discmakers.com/techsupport 10 Chapter 2: Operation This chapter shows each of the menu options and how they are used. 1. C

User Guide v.1.0 www.discmakers.com/techsupport 11 Choose Partition menu: Use the Up or Down button to find the partition where your master dis

User Guide v.1.0 www.discmakers.com/techsupport 12 Output Spindle. At this point you can either put more discs on to the input spindle and press

User Guide v.1.0 www.discmakers.com/techsupport 13 Go back to the 1. Copy Menu. Use the Up or Down button to navigate to the following screen:

User Guide v.1.0 www.discmakers.com/techsupport 14 2. Test Use the Test menu or Test quick key to simulate the copy process. With simulation, wr

User Guide v.1.0 www.discmakers.com/techsupport 15 Use the Up or Down button to find the 6. Select Burn Speed menu. Press the Enter button on 6

User Guide v.1.0 www.discmakers.com/techsupport 16 7. Master Mode The Master Mode menu is used to select between Single Master mode or Multi Mas

User Guide v.1.0 www.discmakers.com/techsupport 17 9. Hard Drive Setup The Hard Drive Setup menu consists of following sub-menus: 1 Select P

User Guide v.1.0 www.discmakers.com/techsupport 18 9.1 Select Partition The Select Partition submenu is used to select the partition on the Hard

User Guide v.1.0 www.discmakers.com/techsupport 19 Hard Drive Setup 5. Partition Info (002) [FUN ] CD 21MB The system will display a verif

User Guide v.1.0 www.discmakers.com/techsupport 2 Chapter 1: Overview 1. Welcome The Disc Makers Forte autoloader is a reliable, high performanc

User Guide v.1.0 www.discmakers.com/techsupport 20 Hard Drive Setup 6.Format Hard Drive Format Hard Drive Press OK to Continue Setup 1.Langua

User Guide v.1.0 www.discmakers.com/techsupport 21 Setup 2.Read Error Skip Read Error Skip On Read Error Skip Off Setup 3. CD Writing Mode CD Wri

User Guide v.1.0 www.discmakers.com/techsupport 22 Max Audio, VCD & CDG 16x Setup 5. Buzzer Buzzer On Buzzer Off Use the Up or Down button to

User Guide v.1.0 www.discmakers.com/techsupport 23 10.8. Counter This menu allows you to choose whether you want to enable the Counter feature. B

User Guide v.1.0 www.discmakers.com/techsupport 24 12.5 Update Firmware This function will update the software of your writer drive. To update,

User Guide v.1.0 www.discmakers.com/techsupport 25 Chapter 3: Trouble Shooting and Error Codes No display on LCD or the unit does not operate wh

User Guide v.1.0 www.discmakers.com/techsupport 26 Chapter 4: Error Codes List of Error Codes Code Full Description Short Description 10 IF ERRO

User Guide v.1.0 www.discmakers.com/techsupport 27 15 IF ERROR CODE 15 IS SHOWN, IT REPRESENTS THAT THE VACUUM PICKING ARM DID NOT REACH THE DRIVE

User Guide v.1.0 www.discmakers.com/techsupport 28 70 IF ERROR CODE 70 IS SHOWN, IT REPRESENTS THAT A DISC WAS PICKED FROM AN INPUT BIN AND THE VA

User Guide v.1.0 www.discmakers.com/techsupport 3 2. The LCD Control Panel Figure 1-4 below shows the LCD Control Panel. This panel has a two-lin

User Guide v.1.0 www.discmakers.com/techsupport 4 1. Copy: page 10 Use the Copy menu to make copies of a master disc or hard drive image. Before

User Guide v.1.0 www.discmakers.com/techsupport 5 duplication. At this point, Hard Drive is the only place where the content of the master disc re

User Guide v.1.0 www.discmakers.com/techsupport 6 7. Screen Saver Use this setting to enable or disable the Screen Saver feature. When this is en

User Guide v.1.0 www.discmakers.com/techsupport 7 This function is used to update the firmware of your robotics, if instructed by technical suppor

User Guide v.1.0 www.discmakers.com/techsupport 8 for job A) the autoloader will load entire content of this disc(Master A) into the reserve parti

User Guide v.1.0 www.discmakers.com/techsupport 9 To enter the number, you need to use the Up or Down button to select the number for each digit a